Stairs by floor height · 9 ft 3 in · Straight
Straight stairs for a 9 ft 3 in floor height
16 risers of 6 15/16″ and 15 treads 11″ deep, at 32°. 36″ wide, it takes 3′ × 13′ 9 3/8″ of floor. It is 13′ 9 3/8″ long and needs an opening of 11′ 5 5/8″ in the floor above for 2 m clear over every nosing.
Open this stair in uCADWhat it’s made of
More or fewer steps
9 ft 3 in (111″) can be climbed in fewer, higher steps or more, lower ones. Each opens in uCAD as this stair with that many risers.
| Risers | Each riser | Going | Pitch | Run of a straight flight | How it walks | In uCAD |
|---|---|---|---|---|---|---|
| 14 | 7 15/16″ | 9 13/16″ | 39° | 10′ 7 15/16″ | over the IRC’s 7¾″ riser | open |
| 15 | 7 3/8″ | 9 13/16″ | 37° | 11′ 5 13/16″ | treads under the IRC’s 10″ | open |
| 16 | 6 15/16″ | 11″ | 32° | 13′ 9 3/8″ | comfortable (drawn here) | open |
| 17 | 6 1/2″ | 11 13/16″ | 29° | 15′ 9″ | comfortable | open |
The IRC (US homes) allows risers up to 7¾″ and asks for treads of at least 10″, 6′8″ of headroom and a width of 36″; states and towns amend it. Check the code that applies to yours.
What it’s made of
Drawn as it’s built, in timber with open treads: treads housed in the stringers, posts under the turns, a railing on its newels. 299 parts in all, every bolt and weld among them. Sizes in inches, length × width × thickness.
| Part | Qty | Length | Width | Thickness |
|---|---|---|---|---|
| stringer (shaped) | 2 | 193 1/16″ | 10 3/8″ | 1 15/16″ |
| tread | 13 | 37 3/16″ | 12″ | 1 9/16″ |
| tread (shaped) | 2 | 37 3/16″ | 12″ | 1 9/16″ |
| handrail, round 50 mm (shaped) | 2 | 188 7/8″ | 1 15/16″ | 1 15/16″ |
| post, timber 90x90 | 2 | 54 1/16″ | 3 9/16″ | 3 9/16″ |
| post, timber 90x90 | 2 | 46 7/8″ | 3 9/16″ | 3 9/16″ |
| baluster, steel square bar 18 mm (shaped) | 62 | 33 3/8″ | 11/16″ | 11/16″ |
Fixings: 4 × tie rod M10x1041, 32 × washer M10, 24 × nut M10, 62 × stud M8x80, glued, 62 × screw 5x45, 2 × bracket, concealed post base 90, 4 × anchor bolt M10x100, 4 × stud M10x117, 4 × anchor bolt M10x200, 8 × bolt M10x170, 8 × nut M10, barrel.
Closed risers, a steel frame, another width or railing: change it in uCAD, and the parts are worked out again, with a cut list of the boards to buy. Sizes of the structure are the library’s defaults for a house stair, not an engineer’s calculation for yours.
Another height or width
Will it fit your room?
Open it in uCAD, draw your walls round it and look: turn it the other way, move the turn up or down, change the width. Or tell the AI: “a stair for 9 ft 3 in in a 7 × 10 ft stairwell”, and it draws one that fits.
Same height: L-shaped, landing · L-shaped, winders · U-shaped, landing · U-shaped, winders · Spiral · Square spiral
This stair for 9 ft · 9 ft 6 in · all heights